The Modal Shop

  • 9907-ADP026

    Calibration Mounting Adaptor for model 9907C. Supports sensors with 0.32″ diameter diaphragm, 0.625″ hex mounting shoulder, 0.43″ protrusion, and 3/8-24 mounting thread. Common sensors supported are Kulite HEM-375.

    Publié le 


  • 9907-ADP025

    Calibration Mounting Adaptor for model 9907C. Supports sensors with 0.148″ diameter diaphragm, 0.375″ hex mounting shoulder, 0.760″ protrusion, and 10-32 mounting thread. Common sensors supported are Kulite XTL-190L.

    Publié le 


  • 9907-ADP024

    Calibration Mounting Adaptor for model 9907C. Supports sensors with 0.148″ diameter diaphragm, 0.375″ hex mounting shoulder, 0.437″ protrusion, and 10-32 mounting thread. Common sensors supported are Kulite XTL-190.

    Publié le 


  • 9901-D-M-010

    Mylar diaphragm for 9901C series. 0.010 inches [0.3 mm] thick. Package of 25.

    Publié le 


  • 9901-D-M-001

    Mylar diaphragm for 9901C series. 0.001 inches [0.03 mm] thick. Package of 25.

    Publié le 


  • 9901-D-A-064

    Aluminum diaphragm for 9901C series. 0.064 inches [1.6 mm] thick. Package of 25.

    Publié le 


  • 9901-D-A-040

    Aluminum diaphragm for 9901C series. 0.040 inches [1 mm] thick. Package of 25.

    Publié le 


  • 9901-D-A-032

    Aluminum diaphragm for 9901C series. 0.032 inches [0.8 mm] thick. Package of 25.

    Publié le 


  • 9901-D-A-020

    Aluminum diaphragm for 9901C series. 0.020 inches [0.5 mm] thick. Package of 25.

    Publié le 


  • 9535C-UPG

    Upgrade of Manual 9525C to Automated 9535C shock test capability. Includes 9535C controller, cable guide and updated software key file. Requires 9155 Software Ver. 7.4.0 or later. Please consult TMS for upgrade of earlier software versions.

    Publié le 


  • 9525C-RCG

    Reference Cable Guide upgrade kit for PneuShock Tower.

    Publié le 


  • 9525C-PA

    Projectile assembly for TMS PneuShock (9525C or 9535C). Replacement part for worn assemblies. Includes projectile and elastomer ring.

    Publié le 


  • 9155-MNT94

    Calibration System Mounting Adaptor. For sensors with 2-56 UNF male mounting thread. For use on 10-32 shakers. Includes 2-56 SHCS and hex wrench.

    Publié le 


  • 9155D-CBL42

    Accessory SUT cable for use with RV646B02 sensor to measure raw voltage output and 4-20 mA output. 3-Pin MIL-C-5015 to flying leads.

    Publié le 


  • 9155-CBL41

    Accessory SUT cable for use with 9155D-USC or 9155D-427 (with 9155-CBL34) for bridge sensor connection. 6 pin Phoenix Connector to IC clips.

    Publié le 


  • 9155-CBL40

    Accessory SUT cable for use with 9155D-427 signal conditioning for bridge sensor connection. 8-socket mini DIN to 6 pin Phoenix Connector. Includes (1) Phoenix screw terminal block plug.

    Publié le